uslockdoc

Locksmith Blog & News

Tips to Adjust Your Door Strike Plate and 2 Reasons Why You Might Need To Do This

tips to adjust your door strike plate

What is a door strike plate?

Your door strike plate can become misaligned for many reasons. There are several steps you can take to repair it. First, you will need to check the screws on the hinges and make sure they are secure. If they are loose, the door will not hang properly. Next, you will want to check that the strike plate is properly aligned.

Misalignment problems with the strike plate

If you have noticed that your door is not closing properly, or you have a misaligned latch, your strike plate may need to be adjusted. This is important because the strike plate is responsible for preventing friction between the door and the frame. Misaligned plates can weaken the hinges and door frame, as well as cause security problems. There are several ways to correct the problem.

Adjusting the strike plate is not difficult. If the hole in the strike plate is too small for the latch bolt, you can fill the gap with paintable wood filler. You can also widen the hole with a file. Using wood dowels to fill in old screw holes is also a common fix for door alignment issues. Ensure that the dowels are a close match to the diameter of the screw holes. Wood glue will help you secure the dowels in the old holes.

Adjusting the strike plate can be done incrementally with a hammer and a screwdriver. The position of the new one should overlap the old one, but not the screw holes. Depending on the amount of misalignment, you may need to remove the it altogether.

Ideally, you should adjust the strike plate along two axes: forward or backward, and in or out. To accomplish this, you must carefully maneuver the plate into position. Once you have placed the strike plate in the desired location, you can tighten the screws. For a smaller adjustment, you can use longer hinge screws. These long screws can be used to raise or lower the latch.

Another common fix for a misaligned door is to realign the hinges. When hinges are not lifting the door to its fullest potential, they can sag, causing the door to sag too. This can cause the latch to sit too low in the strike plate and prevent the door from closing. Alternatively, you can adjust the knuckles to align them with the bottom hinge.

A more severe case of misalignment will require you to remove the strike plate. It is advisable to never use new screws that are too close to the existing ones. Otherwise, the connection between the strike plate and the door frame will be compromised.

Removing the strike plate can be done in three ways: backward, forward, or up. In order to move the strike plate up, you will need to loosen the screws. Place a hammer on top of the screwdriver and tap the top of the screwdriver until the new position is achieved. Similarly, moving the strike plate down can be done in the same way.

Before attempting any extreme adjustments to the strike plate, you should first consider whether there are any other underlying causes that might be causing the misalignment. Some of these underlying causes are the latch, the lock, the doors, and even the foundation. Other causes include humidity and improper ventilation.

Repairing a door that won’t latch

If your door won’t latch, there are a few simple steps to get it working again. First, check to make sure that the hinges are securely attached. Also, tighten any loose screws. Then, you can move the strike plate to the right position. Alternatively, you can buy an adjustable strike for the door. These are usually available at your local home improvement store.

One of the easiest ways to fix a door that won’t latch is to adjust the strike plate. This is because the latch should be able to reach the plate. However, it is possible that the hole for the plate is too small to accommodate the latch. For this reason, you need to enlarge the strike plate hole. To do this, you can either shave off some of the metal on the plate or file the edges to expand the opening.

A small piece of masking tape or pipe sealant can be used to mark the location of the strike plate. You can then use the marking material to reposition the strike plate. Another option is to remove the old strike plate and replace it with a new one. Afterwards, you should fill the old hole with wood putty. Wooden shims can also be inserted to raise the bottom of the door and reposition the plate.

While there are many other ways to fix a door that won’t close, these are some of the most basic. Using an enlarger or a file, you can enlarge the plate hole to allow the latch to fit. Adding a spacer between the hinge and the jamb can also help.

The best tool for widening the strike plate hole is a half-round file. Make sure to match the curvature of the latch hole with the curve of the file. When you have finished, you should have a nice sized hole for the latch.

You can also test the strength of your lock by slamming the latch. However, this isn’t the best way to check if the latch is able to pull your door back into place. That’s because you’ll also need to check the height of the latch. It’s also likely that your hinges are not aligned. Changing them can be a good solution, but it’s better to do it the right way.

In the end, you’ll need to decide whether or not your door is truly unlatchable. This will depend on the reason for your problem. Generally, if the door won’t latch, it’s probably due to a misaligned latch. On the other hand, if the latch is unable to retract, it’s probably because the hinges are too loose.

Finally, you can try to adjust your hinges. This is not a hard task, but it can be tricky. Use a phillips-head screwdriver to tighten any loose screws. Don’t forget to put on a pair of goggles before you begin.

If you like what you read, check out our other articles here.

SOCIAL MEDIA
Facebook
Twitter
LinkedIn
JOIN OUR NEWSLETTER!

Check out our monthly newsletter and subscribe to your topics!

Subscribe to our Newsletter

Ready to get started, Get our Newsletter and join the Community!
BLOG INSPIRATION

More Weather Articles & News

Other articles that may be of interest

Get A Free Quote

Locksmith in workshop makes new key, use grinding engraving machine